Update your scripts to load br_netfilter if you need this. bridge: automatic filtering via arp/ip/ip6tables has been deprecated. eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 1 squashfs-split partitions found on MTD device rootfs mtd: device 2 (rootfs) set to be root filesystem 8 cmdlinepart partitions found on MTD device spi0.0 Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled io scheduler deadline registered (default) jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. squashfs: version 4.0 (1) Phillip Lougher futex hash table entries: 256 (order: -1, 3072 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) UDP hash table entries: 256 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 0, 4096 bytes) pci_bus 0000:01: No busn resource found for root bus, will use pci_bus 0000:00: No busn resource found for root bus, will use registering PCI controller with io_map_base unset Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) PID hash table entries: 512 (order: -1, 2048 bytes) Kernel command line: board=F9K1115V2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd Built 1 zonelists in Zone order, mobility grouping on. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Initrd not found or empty - disabling initrd SoC: Qualcomm Atheros QCA9558 ver 1 rev 0 # Giving linux memsize in bytes, 134217728 # Transferring control to Linux (at address 80060000). Image Type: MIPS Linux Kernel Image (lzma compressed) TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00000001 TEST: FINAL XMII VAL after RX Calibration - 0x5a000000 TEST: FINAL REG VAL after TX Calibration - 0x4a000000 Using fixed addressĪth_gmac_enet_initialize: reset mask:c02200 Reserving 128k for boot params() at: 87f73fb0įlash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18 Reserving 36 Bytes for Global Data at: 87f93fb0 Reserving 44 Bytes for Board Info at: 87f93fd4 Top of RAM usable for U-Boot at: 88000000 Actual data throughput will be lower and may depend on the mix of wireless products used.Ath_ddr_initial_config(200): (32bit) ddr2 init The standard transmission rates-300Mbps or 867Mbps (for 5GHz), 300Mbps (for 2.4GHz), 54Mbps, and 11Mbps-are the physical data rates. In order to achieve the best performance, router must be used with a compatible wireless device. Actual speeds will vary depending on a number of factors. Up to 2.8x faster physical data rate when compared to 802.11n Wi-Fi routers using two antennas to transmit and receive data. Works seamlessly with ‘N’ and ‘G’ Wi-Fi devices.Ĭonnect multiple wired devices at gigabit speeds. Browser-based window uses your smartphone, tablet or computer to install your router in just minutes.īelkin’s proprietary Intellistream QoS (Quality of Service) automatically prioritizes video and gaming.Įxclusive MultiBeam antenna technology provides maximum coverage virtually anywhere in the home.īlocks unsafe and inappropriate content automatically for all the devices on your network. Get the fastest dual-band speeds for video streaming and gaming-up to 300Mbps (2.4GHz) + 867Mbps (5GHz)† for delivering maximum speed to multiple devices. Optimized performance for a new level of speed and reliable coverage to all your Wi-Fi devices. Features: Up to 2.8x Faster Than N Technology
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |